Why is my Toppay USDT deposit pending?

A transfer can be waiting on blockchain confirmations or on the platform crediting it after confirmations complete. Check your TxID on the blockchain explorer first, then your dashboard status.

What happens if I send USDT on the wrong network?

In most cases the funds are not recoverable, because the receiving address does not exist on the network you used. This is why the network must be matched exactly before sending.

Should I send a second USDT transaction if the first has not arrived?

No. Wait and verify the first transaction using its hash. Sending again while the first is pending frequently results in a duplicate transfer.

Which USDT network is cheapest?

TRC20 on Tron generally has the lowest fees and fastest confirmations, which is why it is the most widely used for USDT transfers in India. Always use whichever network your account deposit screen specifies.

Toppay USDT Guide | USDT Deposit, Withdrawal & Network Checks

Toppay USDT transactions are irreversible. There is no support ticket that undoes a transfer sent on the wrong network or to a wrong address — not on this platform, not on any platform, because the limitation is in the blockchain, not the service. Everything on this page exists to make sure that never happens to you.

Read this fully before your first USDT transaction. It takes three minutes and it is the highest-value three minutes on this site.

The single most important concept: networks

USDT (Tether) is not one thing. The same token is issued on several separate blockchains, and each one is a completely independent system:

TRC20 — on the Tron network. Addresses start with T. Low fees, fast, the most commonly used for USDT in India.
ERC20 — on Ethereum. Addresses start with 0x. Higher fees, especially when the network is busy.
BEP20 — on BNB Smart Chain. Addresses also start with 0x, which is exactly why ERC20 and BEP20 get confused.

Sending USDT on one network to an address that expects another usually means permanent loss. The ERC20/BEP20 case is the most dangerous because the addresses look identical in format. The only thing that distinguishes them is the network setting you choose at send time.

Before a USDT deposit

Open your signed-in account and find the deposit screen. Read the network shown there. Do not rely on memory or an older screenshot.
Copy the address using the copy button, never by typing it manually.
Set the same network in your sending wallet or exchange. Match it exactly — TRC20 to TRC20, not “Tron” to “Ethereum”.
Verify the full address after pasting. Compare the first six and last six characters against the source, and ideally a section from the middle. Clipboard-hijacking malware swaps addresses on paste, and it produces an address with a similar-looking start and end.
Send a small test amount first if this is a new address. Confirm it arrives before sending the remainder.
Save the transaction hash (TxID) that your sending wallet gives you. Without it, nothing can be traced.

Understanding confirmations

After you send, the transaction enters the network and waits for blocks to confirm it. TRC20 usually confirms within about a minute; ERC20 depends heavily on network congestion and gas price.

A transfer shown as “pending” can be waiting on either of two separate things: blockchain confirmations, or the platform’s own crediting process after confirmations complete. These are different stages. Check the blockchain explorer for the first, and your dashboard for the second.

Do not send a second transaction while the first is pending. This is the most common and most expensive mistake made in this entire category. If the first transaction eventually completes, you have now sent twice.

USDT to INR

The calculator on this page gives you a quick estimate of what a USDT amount is worth in rupees at a rate you enter. Use it for planning — the actual rate, fees and final credited amount for your transaction are whatever your signed-in dashboard shows at the moment you confirm. A dedicated converter with more explanation is on the USDT to INR page.

Before a USDT withdrawal

Confirm the destination address belongs to a wallet you control.
Confirm the destination wallet supports the network you are withdrawing on.
Check the minimum withdrawal amount and the network fee shown on the withdrawal screen.
Paste the address, then verify start, middle and end characters.
Withdraw a small test amount first when using a new address.

Full detail is on the Toppay withdrawal guide.

Troubleshooting a stuck USDT transaction

Sent, nothing received — look up your TxID on the correct blockchain explorer. If the explorer shows it confirmed to the right address, the issue is crediting, not the transfer, and support can act on the TxID.
Wrong network used — check whether the receiving address exists on the network you sent on. In most cases these funds are not recoverable. Report it with the full TxID anyway.
Wrong address entirely — if the address belongs to another exchange, contact that exchange with the TxID. Otherwise recovery is not possible.
Amount below minimum — deposits under the stated minimum may not credit automatically.

Safety rules for USDT

Never share your wallet seed phrase or private key with anyone, for any reason.
Never let anyone screen-share while you access a wallet or the platform.
Beware “address poisoning”: a dust transaction from an address resembling one of yours, hoping you copy it from history later. Always copy from the source, never from transaction history.
Anyone offering to double your USDT is running a fraud. There are no exceptions to this.

Last updated: 2026-08-15 · Published by TopPay · Read the disclaimer

Toppay USDT Guide